2014-08-24 19:18:18 +02:00
|
|
|
|
<chapter xmlns="http://docbook.org/ns/docbook"
|
|
|
|
|
|
xmlns:xlink="http://www.w3.org/1999/xlink"
|
|
|
|
|
|
xmlns:xi="http://www.w3.org/2001/XInclude"
|
|
|
|
|
|
version="5.0"
|
|
|
|
|
|
xml:id="ch-file-systems">
|
|
|
|
|
|
|
|
|
|
|
|
<title>File Systems</title>
|
|
|
|
|
|
|
|
|
|
|
|
<para>You can define file systems using the
|
|
|
|
|
|
<option>fileSystems</option> configuration option. For instance, the
|
|
|
|
|
|
following definition causes NixOS to mount the Ext4 file system on
|
|
|
|
|
|
device <filename>/dev/disk/by-label/data</filename> onto the mount
|
|
|
|
|
|
point <filename>/data</filename>:
|
|
|
|
|
|
|
|
|
|
|
|
<programlisting>
|
|
|
|
|
|
fileSystems."/data" =
|
|
|
|
|
|
{ device = "/dev/disk/by-label/data";
|
|
|
|
|
|
fsType = "ext4";
|
|
|
|
|
|
};
|
|
|
|
|
|
</programlisting>
|
|
|
|
|
|
|
|
|
|
|
|
Mount points are created automatically if they don’t already exist.
|
|
|
|
|
|
For <option>device</option>, it’s best to use the topology-independent
|
|
|
|
|
|
device aliases in <filename>/dev/disk/by-label</filename> and
|
|
|
|
|
|
<filename>/dev/disk/by-uuid</filename>, as these don’t change if the
|
|
|
|
|
|
topology changes (e.g. if a disk is moved to another IDE
|
|
|
|
|
|
controller).</para>
|
|
|
|
|
|
|
|
|
|
|
|
<para>You can usually omit the file system type
|
|
|
|
|
|
(<option>fsType</option>), since <command>mount</command> can usually
|
|
|
|
|
|
detect the type and load the necessary kernel module automatically.
|
|
|
|
|
|
However, if the file system is needed at early boot (in the initial
|
|
|
|
|
|
ramdisk) and is not <literal>ext2</literal>, <literal>ext3</literal>
|
|
|
|
|
|
or <literal>ext4</literal>, then it’s best to specify
|
|
|
|
|
|
<option>fsType</option> to ensure that the kernel module is
|
|
|
|
|
|
available.</para>
|
|
|
|
|
|
|
2017-04-30 14:10:30 +02:00
|
|
|
|
<note><para>System startup will fail if any of the filesystems fails to mount,
|
|
|
|
|
|
dropping you to the emergency shell.
|
|
|
|
|
|
You can make a mount asynchronous and non-critical by adding
|
|
|
|
|
|
<literal>options = [ "nofail" ];</literal>.
|
|
|
|
|
|
</para></note>
|
|
|
|
|
|
|
2014-08-26 15:45:47 +02:00
|
|
|
|
<xi:include href="luks-file-systems.xml" />
|
2014-08-24 19:18:18 +02:00
|
|
|
|
|
|
|
|
|
|
</chapter>
|
