Now we're doing this at the point where we're saving the VM state.
Unfortunately it's not quite right, because the controller VM is shut
down _before_ we're saving the state, so the share gets disconnected
despite autodisconnect being deactivated during setup.
We can get around this issue by finally introducing the xchg share,
which is the last item to be implemented before we can merge to master.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
These stages are in particular:
* Install of the bare Windows VM with Cygwin and shut down.
* Boot up the same VM again without the installation media and dump the
VMs memory to state.gz.
* Resume from state.gz and build whatever we want to build.
Every single stage involves a new "controller", which is more like an
abstraction on the Nix side that constructs the madness described in
276b72fb93.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
This SSH key is specifically only for accessing the installed Cygwin
within the Windows VM, so we only need to expose the private key. Yes,
you heard right, the private key. It's not security-relevant because the
machine is completely read-only, only exposed to the filesystem and
networking is not available.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
At least the largest portion of the installer, because in the end we
don't want the installer to *actually* save the state but only prepare
the base image.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
After quite a lot of fighting against Windows and its various
limitations, this new is the base architecture for installing and
accessing the Windows VM and thus the Cygwin environment inside it:
.------------.
.---> | vde_switch |
| `-[#]----[#]-'
| | |
,' .' `---.___
,' 192.168.0.1 `.
| | 192.168.0.2
,' _____[#]____ |
,' | | ______[#]______
| | Windows VM | | .--' |
| |____________| | | |
| | /|\ | .-| |
| .---------. | | | | | |
.-|-| manager |-' | | | | |
| | `---------' | | | | |
| | | | | | |
| | .-------------. | | Samba |
| | | BOOTSTRAP | | | | | |
| | |-------------| | | | | .------|
| `-| spawn VMs |-+--> | | `---| xchg | <-------.
| |-------------| | | .---^------| |
| | install |---. | `-| nixstore | <----. |
| |-------------| | | `----------| | |
|---| suspend VM | | | | | |
| `------.------' | | Controller VM | | |
| | | |_______________| | |
| .--' | /|\ VirtIO
| | __|__________:____________ | |
| \|/ | | `. | | |
| .------------. | | : | | |
| | REAL BUILD | | | .-------^--------. | | |
| |------------| | `-> | serial console | | | |
`-| revive VM | | `----------------' | | |
|------------| |------------. | | |
| build |-->| /nix/store >>>-----------|-' |
|------------| |------------| | |
| collect |<--| xchg >>>-----------|----'
`-----.------' |------------' |
| | |
\|/ | | | __ ___ | |
| |--| | | (__ -|- |
F I N I S H E D | | | |__| ___) | |
|__________________________|
This might look a bit overwhelming, but let me try to explain:
We're starting at the base derivation ("BOOTSTRAP" above), where we
actually install the Cygwin envirenment. Over there we basically fire up
a vde_switch process and two virtual machines: One is the Windows
machine, the other is a NixOS machine, which serves as some kind of
proxy between the host and the Windows machine.
The reason we're doing this, is because we don't have a lot of options
for sharing files between a stock Windows machine and the host. In
earlier experiments, I've tried to communicate with the Windows guest by
using pipes and OpenSSH, but obviously this wasn't a big speed rush (or
to say it bluntly: It was fucking slow).
Using TCP/IP directly for accessing the guest would have been another
option, but it could lead to possible errors when the port or a range of
ports are in use at the Host system. Also, we would need to punch a hole
into the sandbox of the Nix builder (as it doesn't allow networking),
which in turn will possibly undermine deterministic builds/runs (well,
at least as deterministic as it can be, we're running Windows,
remember?).
So, let's continue: The responsibility of the NixOS (controller) VM is
to just wait until an SSH port becomes available on the Windows VM,
whereas the Windows VM itself is installed using an unattended
installation file provided via a virtual floppy image.
With the installation of the basic Windows OS, we directly install
Cygwin and start up an OpenSSH service.
At this point the bootstrapping is almost finished and as soon as the
port is available, the controller VM sets up Samba shares and makes it
available as drive letters within Windows and as bind mounts (for
example /nix/store) within Cygwin.
Finally we're making a snapshot of the memory of the Windows VM in order
to revive it within a few seconds when we want to build something.
Now, the build process itself is fairly straightforward: Revive VM and
build based on existing store derivations and collect the result _and_
the exit code from the xchg share/directory.
Conclusion: This architecture may sound a bit complicated, but we're
trying to achieve deterministic and reproducable builds and/or test
runs.
Signed-off-by: aszlig <aszlig@redmoonstudios.org>
